Plain Gloves and Scarf Pattern #S-107

Printer-friendly versionPrinter-friendly version
Plain Gloves and Scarf Pattern

These are serviceable and smart — yet very comfortable and warm. A smooth fitting scarf — strategically ribbed to eliminate bulkiness at neck.

MATERIALS:
CHADWICK'S RED HEART KNITTING WORSTED, 4 skeins (2 oz. skeins) for scarf; 2 skeins for plain gloves.
Milward's Casein Knitting Pins, 1 pair No. 5 (4 mm. size) for Scarf.
4 double-pointed bone knitting needles No. 5 (4 mm. size) for Gloves.

GAUGE: 5½ sts make 1 inch; 7 rows or rnds make 1 inch.

SCARF No. S-107

With pair of needles, cast on 66 sts. Work 15 inches in stockinette stitch (k 1 row, p 1 row). Work 12 inches in ribbing of k 1, p 1. Work 15 inches more in stockinette stitch (42 inches total length). Bind off loosely. Work 1 row of single crochet around, except along sides of ribbing. Press through damp cloth with hot iron.

PLAIN GLOVES No. S-107

Sizes Small, Medium and Large

LEFT HAND … Using the double-pointed needles, cast on loosely 36 sts for small size; 38 sts for medium size; 40 sts for large size. Divide sts on 3 needles and join, being careful not to twist. Work around in ribbing of k 1, p 1 for 3 inches. Now work in stockinette stitch (k each rnd) for 3 rnds. Then start shaping for thumb as follows: 1st rnd: P 1, inc. 1 st in next st, k 1, inc. 1 st in next st, p 1, k around. 2nd and 3rd rnds: P 1, k 5, p 1, k around. 4th rnd: P 1, inc. in next st, k 3, inc. in next st, p 1, k around. 5th and 6th rnds: P 1, k 7, p 1, k around. 7th rnd: P 1, inc. in next st, k 5, inc. in next st, p 1, k around. Continue thus, increasing 2 sts in thumb gore every 3rd rnd, until there are 11 sts between the 2 p-ribs for small size; 13 sts for medium size, or 15 sts for large size. Next rnd: P 1, slip the thumb sts onto a safety pin to be worked later; cast on 5 sts, k to complete rnd (38 sts on needle for small size; 40 sts for medium size, or 42 sts for large size). Discontinue p-ribs and work around in stockinette stitch, until glove, when tried on, reaches to the base of the fingers (about 1½ inches for small size; 1¾ inches for medium size, or 2 inches for large size). Put glove on. Mark fingers by putting safety pin on palm and back of hand between each finger, having 11 sts for forefinger, 10 sts for middle finger, 8 sts for ring finger and 9 sts for little finger for small size; (1 st more for forefinger and ring finger for medium size, or 1 st more for each finger for large size). When odd number of sts is required for a finger, always have the larger number of sts on the back of the hand with 1 st less on the palm. K around to where the sts are marked off for the little finger, k the sts for the little finger and take the remaining sts off on a strand of yarn to be worked later.

LITTLE FINGER … Divide the sts for the little finger on 3 needles, cast on 2 sts for inner side of finger and work around until finger, when tried on, reaches ½ inch from fingertip (about 1¾ inches for small and medium sizes, or 2 inches for large size). Then * k 1, k 2 tog. Repeat from * around. Work 1 rnd straight. Next rnd: K 2 tog. around. Break yarn, leaving a 6-inch end. Thread this end into needle and run through remaining sts. Draw tight and darn in end to reinforce tip.

RING FINGER … Pick up sts for ring finger from strand of yarn and 2 sts where the 2 sts were cast on for the little finger; cast on 2 sts between palm and back of hand as before. Divide the sts on 3 needles and work around until ½ inch from tip (about 2½ inches in all). Then shape tip as follows: 1st rnd: * K 2 tog., k 2. Repeat from * around. Work 1 rnd straight. 3rd rnd: * K 2 tog., k 1. Repeat from * around. K 1 rnd straight. 5th rnd: K 2 tog. around. Break yarn and finish as for little finger.

MIDDLE FINGER … Pick up the sts for middle finger, 2 sts on 2 sts cast on for ring finger and cast on 2 sts between palm and back of hand. Work about 2¾ inches (½ inch from fingertip) and finish as for ring finger.

FOREFINGER … Pick up sts for forefinger and 2 sts on the 2 sts cast on for middle finger. Work as for ring finger.

THUMB … Pick up the sts from safety pin for thumb and 3 sts on the 5 cast-on sts. Work straight for about 2 inches and finish as for ring finger.

RIGHT HAND … Work to correspond.
Press through damp cloth with hot iron.